-
Comparison of Radio Brand...
Forum: General
Last Post: greggold
3 hours ago
» Replies: 5
» Views: 81 -
Videos: RC Flying
Forum: General
Last Post: srl
07-03-2024, 08:58 AM
» Replies: 759
» Views: 602,000 -
Updating firmware on Mate...
Forum: General
Last Post: caffeine
11-02-2024, 07:18 AM
» Replies: 4
» Views: 89 -
Elrs Gemini is here!
Forum: General
Last Post: greggold
21-01-2024, 10:35 AM
» Replies: 1
» Views: 112 -
VTOL
Forum: General
Last Post: greggold
20-01-2024, 12:56 PM
» Replies: 0
» Views: 48 -
using a gyro with a Radio...
Forum: General
Last Post: greggold
03-01-2024, 12:51 PM
» Replies: 0
» Views: 99 -
A guide to arming elrs fo...
Forum: General
Last Post: secant0give
01-01-2024, 07:12 PM
» Replies: 4
» Views: 441 -
Fuzzy understanding of RC...
Forum: General
Last Post: greggold
29-12-2023, 12:19 PM
» Replies: 0
» Views: 108 -
Videos: Other
Forum: General
Last Post: srl
16-12-2023, 10:19 AM
» Replies: 212
» Views: 142,910 -
Dynamic power on the RM T...
Forum: General
Last Post: greggold
04-12-2023, 08:04 AM
» Replies: 10
» Views: 767
- Forum posts:31,182
- Forum threads:1,503
- Members:342
- Latest member:Vitopilot
It arrived this morning and it's Big!!!!!
Had to unpack it to make sure all was ok,
glad I did it when wife was out otherwise she would
have gone balistic at me using the dining room table.
Just for reference that table can sit 8 people for dinner.
Also put F86 next to it for scale.
Now how am I going to get it down to the field??????????
Hi guys....was hoping for an answer on this from someone with more knowledge than I!....
I have one of the HK mossies and am setting up (weather permitting) for the maiden tomorrow.....
I do have another bit of a concern.....since swapping to the MAS props.....my prop nose cones (and the props...? hard to tell) have a bit of a wobble to them....god knows how this happened....either the nut behind the backplate is not sitting flush (I epoxed the nuts to the backplate) or the backplate has become a bit distaughted. However I'm in no mood now to investiage as I took ages to 'fatten out' the prop shaft with a few layers of heatshink to enable the wider shaft hole to fit the prop shaft (this has worked for me quite well in the past)........
may as well make use of the iphone....
I've uploaded the vid of the 'offset prop'.....the other side is not as bad. The prop shaft is DEF not bent....
What do you guys think?? I am risking it? There is no abnormal noises upon rotation at high speeds.
http://www.youtube.com/watch?v=KShHSiT5uT0
Cheers all......
Just a little something that I thought you guys might like to share.
When I was in Norway last year, and passing through Bodø, I dropped into the aviation museum there. Here is some of the photos.
I apologise for the quality, the lighting was so that I could not get it right.
Out the front, a Hawker on a stick... or should I say Hawker på sticker...
Inside the foyer, a Freedom Fighter on two sticks
In the adjoining airforce base, a F104 Startfighter on a stick
Norwegians like putting things on sticks, so it seems.
MY MOSQUITO!!! (I failed to sneak it out. In fact I failed to budge it at all).
F104 not on stick
Lil' DeHavelin, just hanging out
This Ju88 was placed just as it was recovered. Including bonus Moose.
The Spit again.
Hey guys, I haven't been down the shop since it became Hobbyking. Do they still do over the counter sales?. I can't find any info on opening times anymore.
I was looking at heading down there saturday arvo and looking at radios and this: http://www.hobbyking.com/hobbyking/store...duct=17529 for when I am allowed to fly it
I think I have enough gear now to justify the need of a carry case. Where do I buy one?
Came across this video while browsing the web.
I found it quite interesting and thought some of
you may find it the same.
http://www.youtube.com/watch?v=xRyOXDGgIh8
Thought I would do a build thread to show everyone
how I go about rebuilding an old airframe.
This is my old Parkzone P51 which has seen better days and
after some very rough treatment I fibreglassed and repainted.
Again she was showing signs of neglect most due
to dreaded torque roll on my hand launches.
This time I'm going to install a set of mechanical retracts that I've
had lying about for over a year.
Also, I'm going to try a couple of new building tecniques that I've been
reading about on various forums.
Ok first up Off with the old paint and fibreglass.
Lots of stuff to come off
Mustn't forget the cockpit.
As you can see I've got a bit of work to do with the sanding and filling
so stay tuned for the next installment.
The following equipement was stolen from a PEMAC member, if anyone tries to sell you any of these items please contact PEMAC or leave a message on the Contact page of this web site:
1. 1x JR PCM9XII Tx (with Spektrum 2.4 GHz Module)
2. 1x Spektrum 6Xi Tx
3. Red Aluminium Toolbox with ESCs, Motors, servos, spare parts
4. Yellow/Black Tool box with misc spare parts and tools
5. Green Camo SU-34 EDF Jet
Thanks
Viper Pics
http://www.hobbyking.com/hobbyking/store...duct=15534
Customed Mounted Edf into Viper
http://www.hobbyking.com/hobbyking/store...duct=17221
Bench Tested Install 1000watts, 1.5 kg Static Thrust, 47 Amps, 6s lipo setup
(No Adjustments Done Yet with Tweaking of Timing)
Steve
Looking for a bargain Dx6i
- Used in GWC
- Prepared to pay upto 60% of retail ie 0.60 * $220 = $132
Pls contact me sujit.au@gmail.com